Mixture of solvents based on alcohol, method C according to EN ISO 3452-1
Dries slowly
Flash point material +13 °C
Suitable for all metals (suitability for plastics needs testing prior to use)
Processing temperature -10 to +50 °C
Aerosol can overhead sprayable
Relevant approvals and specifications
Sample testing acc. to EN ISO 3452-2 and ISO 3452-6
Low content of halogens and sulphur according to EN ISO 3452-2
and ASME Code V, Section V, Article 6
In correspondence with Lloyd's Reg., Bureau Veritas, Det Norske Veritas, admitted
by Framatome ANP
Application:
Remove tinder, rust and other contaminations from surface in a suitable manner.
You can use MR85 Remover as precleaner for removal of oils or fats.Apply MRPenetrant to the part to be tested either by spraying, brushing, flooding
or dipping. Allow to penetrate for at least 5 minutes.Remove excess MRPenetrant from surface using a clean lint-free cloth lightly
moistened with MR85 Remover.Spray MR? Developer (e.g. MR70) from a distance of approx. 20 cm on the dry
surface, achieving a thin, uniform layer. Depending on the used penetrant, surface
defects will appear as red or fluorescent indications. Please note: If the developer
layer is too thick tiny discontinuities will not appear through the developer.
Minimum shelf life:
Will keep for a minimum of 4 years, stored at room temperature
Pack sizes:
Aerosols, 500 ml (1 box contains 12 aerosols)
5 L, 30 L, 200 L
Valve pen (Piccolo-Pen)
MR CHEMIE清潔劑MR85愛澤工業izeindustries發貨照片
愛澤工業(IZE_INDUSTRIESMR CHEMIE)*經銷、常用備件型號:
MR CHEMIE清潔劑MR79
MR CHEMIE清潔劑MR85
MR CHEMIE清潔劑MR88
MR CHEMIE清潔劑MR91
德國MR CHEMIE顯像劑MR70產品描述
General appearance and composition:
Solvent removable developer for red and fluorescent penetrant testingform d and e according to EN ISO 3452-1
Water mixable
Dries quickly
Processing temperature -30 °C to +50 °C
Aerosol overhead sprayable
Relevant approvals and specifications
Sample testing acc. to EN ISO 3452-2 and EN ISO 3452-6
Low content of halogens and sulphur according to EN ISO 3452-2and ASME Code V, Section V, Article 6
In correspondence with Lloyd's Reg., Bureau Veritas, Det Norske Veritas,admitted by Framatome ANP
Produits et Matériaux Utilisables en Centrales (PMUC)
TLV 9017 01:2011-01
Application:
Remove tinder, rust and other contaminations from surface in a suitable manner. A
possible precleaner for removal of oils or fats is e.g. our remover MR? 79.
Apply MR?Penetrant to the part to be tested either by spraying, brushing, flooding
or dipping. Allow to penetrate for at least 5 minutes.
Remove excess MR?Penetrant from surface either using water or a clean lint-free
cloth lightly moistened with an MR? Remover.
Spray MR? 70 Developer from a distance of approx. 20 cm on the dry surface,
achieving a thin, uniform layer. Depending on the used penetrant, surface defects
will appear as red or fluorescent indications. Please note: If the developer layer istoo thick tiny discontinuities will not appear through the developer.
When using a spray gun connected to compressed air it must be ensured that the
supplied air is free of water and fat.
Minimum shelf life:
Will keep for a minimum of 4 years, stored at room temperature
Pack sizes:
Aerosols, 500 ml (1 box contains 12 aerosols)
5 L, 30 L
Valve pen
MR CHEMIE顯像劑MR70愛澤工業izeindustries發貨照片
愛澤工業(IZE_INDUSTRIESMR CHEMIE)*經銷、常用備件型號:
MR CHEMIE顯像劑MR70
MR CHEMIE顯像劑MR81
MR CHEMIE顯像劑MR703W
MR CHEMIE顯像劑MR703WK
MR CHEMIE磁懸液MR76S composition:
Mixture of isoparaffinic carbonhydroxides, additives and pigments
Serves to indicate cracks when performing coloured magnetic particle inspection